電纜識別儀價格是用于將某一特定電纜從一束電纜中識別出來的儀器。它是一小型化手提式，緊湊型儀器，裝在鋁合金箱內，由一個信號發生器，一個帶傳感器的接收機及連線構成。

電纜識別儀價格簡介：為了可靠準確地識別電纜，需要給被識別電纜加一特殊的信號，該信號要被接收機接收，利用這一特性便能識別出要找的電纜。

工作原理：

發生器將周期性的單極性電壓脈沖饋入要識別的電纜中，該電纜需要在遠端接地，以保證有足夠大的電流流過電纜。該系統要設計成返回電流不要從同一電纜中返回，能做到這一點，饋入電纜中的脈沖電流的方向可做為一明顯的識別標準，流出去的電流僅從這一根電纜通過，所有其它鄰近電纜中流過的都是返回電流，但它們的極性相反。除了電流方向這一實際差異外，電流幅度也是一識別特征，流出去的電流僅通過一根電纜、而返回電流可通過幾根電纜、這意味著流出去的電流比流過其它電纜的返回電流大。

　　接收機的任務是探測流過電纜電流方向以及它的大小。為達到這一目的，電流傳感器被用作傳感器，它帶有一放大器并串聯在電路中，傳感器鉗住被測電纜，電流流過電纜產生的磁場在傳感器的線圈中感應出電壓，該電壓極性由電流方向和傳感器線圈的方向決定。為了得到明顯有電流方向的電壓極性，對一束電纜中所有電纜進行測試都采取相同正確的方向。傳感器線圈中感應的電壓在表頭中顯示出來，如果傳感器按上述方式連接，指針擺動方向可顯示電流方向，即只有電流流出的這根電纜指針向一邊偏，這根就是要找的電纜。所有其它電纜只流過返回電流，指針向另一邊偏、或無脈動電流，指針不偏轉。接收機上的放大調節器可調整信號強度。

二、功能介紹

識別儀主機各部分功能如下：

1.　電源開關：控制整機電源通斷。

2.　電源輸入插座：用儀器所配電源線，輸入50HZ、220V交流電源。儀器使用時，應獨立使用三孔電源插座，插座接地線就近直接接地。

3.　保險座：儀器使用10A保險芯，損壞時應換同規格保險芯。

4.　黑接線柱：測試時，用配套黑色測試線（Ф4插頭）插入此插孔，另一端測試夾接系統地。

5.　紅接線柱：測試時，用配套紅色測試線（Ф4插頭）插入此插孔，另一端測試夾接被測電纜芯線。

6.　表頭：指示輸出電流大小。7.輸出調節；調節輸出電流大小。

7、輸出調節旋鈕：用于輸出幅度大小的調節。以不滿刻度打表為原則。

接收機各部分功能如下：

1. 靈敏度調節：順時針旋轉，接收機電表指示值增大，逆時針旋轉，指示值變小。

2. 表頭：指示輸入信號幅度大小與極性。

三、工作方法

帶電電纜設備儀信號發生器由交流電源供電，它對已斷電的、要識別的電纜加上固定周期單極性的直流脈沖。工作時，將發生器輸出線連在電纜芯線和接地點或地釘上，該電纜線鎧裝與大地斷開，芯線在遠端與接地點或地釘相連，該回路可傳導脈沖電流，它可由識別儀上的表頭讀出，電流大小由環路電阻決定，環路電阻應盡可能小。

為保證環路電阻的阻抗盡可能低，地釘與地之間要保證接觸良好（將地釘附近的地方弄濕）。發射機與電纜連接正確但無輸出，說明環路電阻太大或未構成測試回路，應檢查終端接地。【將發射機兩輸出夾短接，表頭有輸出，證明儀器完好】警告：為確保人身安全，對已確定的電纜，在維修開鋸前，一定要進行扎釘試驗，可選DS1102型電纜安全刺扎器。

四、配套

帶電電纜設備儀主機　　　1臺　　　　

電源線　　　1條

帶電電纜設備儀接收機　　1臺　　　

說明書　　　1本

合格證　　　　　　　　　　1份　　　　

測試線　　　2條

保修卡　　　　　　　　　　1份

注：1.測試時電流鉗上的紅色箭頭標記指向電纜遠端！

2.發射機輸出電流調節大也超不過5A時，應檢查接地電阻，也可另打地釬。【對端芯線接地后，在首端測量芯地間電阻越小，輸出電流越大】

3.發射機正常工作電流應調到大于10A小于30A[5A可工作]，電流大時接收機指示明顯。發射機輸出正常但接收機無指示，大多是卡鉗口未閉合，請張開鉗口，快速讓其卡、卡閉合幾次就可解決問題。